OLED

Jump to: navigation, search 
Prototype OLED lighting panel developed by Lumiotec
Demonstration of a flexible OLED device
OLED TVAn OLED (organic light-emitting diode) is a light-emitting diode (LED) in which the emissive electroluminescent layer is a film of organic compound which emits light in response to an electric current. This layer of organic semiconductor is situated between two electrodes. Generally, at least one of these electrodes is transparent. OLEDs are used to create digital displays in devices such as television screens, computer monitors, portable systems such as mobile phones, handheld games consoles and PDAs. A major area of research is the development of white OLED devices for use in solid-state lighting applications.[1][2][3]

There are two main families of OLED: those based on small molecules and those employing polymers. Adding mobile ions to an OLED creates a light-emitting electrochemical cell or LEC, which has a slightly different mode of operation. OLED displays can use either passive-matrix (PMOLED) or active-matrix addressing schemes. Active-matrix OLEDs (AMOLED) require a thin-film transistor backplane to switch each individual pixel on or off, but allow for higher resolution and larger display sizes.

An OLED display works without a backlight. Thus, it can display deep black levels and can be thinner and lighter than a liquid crystal display (LCD). In low ambient light conditions such as a dark room an OLED screen can achieve a higher contrast ratio than an LCD, whether the LCD uses cold cathode fluorescent lamps or LED backlight.
History The first observations of electroluminescence in organic materials were in the early 1950s by André Bernanose and co-workers at the Nancy-Université, France. They applied high-voltage alternating current (AC) fields in air to materials such as acridine orange, either deposited on or dissolved in cellulose or cellophane thin films. The proposed mechanism was either direct excitation of the dye molecules or excitation of electrons.[4][5][6][7]

In 1960, Martin Pope and co-workers at New York University developed ohmic dark-injecting electrode contacts to organic crystals.[8][9][10] They further described the necessary energetic requirements (work functions) for hole and electron injecting electrode contacts. These contacts are the basis of charge injection in all modern OLED devices. Pope's group also first observed direct current (DC) electroluminescence under vacuum on a pure single crystal of anthracene and on anthracene crystals doped with tetracene in 1963[11] using a small area silver electrode at 400 V. The proposed mechanism was field-accelerated electron excitation of molecular fluorescence.

Pope's group reported in 1965[12] that in the absence of an external electric field, the electroluminescence in anthracene crystals is caused by the recombination of a thermalized electron and hole, and that the conducting level of anthracene is higher in energy than the exciton energy level. Also in 1965, W. Helfrich and W. G. Schneider of the National Research Council in Canada produced double injection recombination electroluminescence for the first time in an anthracene single crystal using hole and electron injecting electrodes,[13] the forerunner of modern double injection devices. In the same year, Dow Chemical researchers patented a method of preparing electroluminescent cells using high voltage (500–1500 V) AC-driven (100–3000 Hz) electrically insulated one millimetre thin layers of a melted phosphor consisting of ground anthracene powder, tetracene, and graphite powder.[14] Their proposed mechanism involved electronic excitation at the contacts between the graphite particles and the anthracene molecules.

Electroluminescence from polymer films was first observed by Roger Partridge at the National Physical Laboratory in the United Kingdom. The device consisted of a film of poly(n-vinylcarbazole) up to 2.2 micrometres thick located between two charge injecting electrodes. The results of the project were patented in 1975[15] and published in 1983.[16][17][18][19]

The first diode device was reported at Eastman Kodak by Ching W. Tang and Steven Van Slyke in 1987.[20] This device used a novel two-layer structure with separate hole transporting and electron transporting layers such that recombination and light emission occurred in the middle of the organic layer. This resulted in a reduction in operating voltage and improvements in efficiency and led to the current era of OLED research and device production.

Research into polymer electroluminescence culminated in 1990 with J. H. Burroughes et al. at the Cavendish Laboratory in Cambridge reporting a high efficiency green light-emitting polymer based device using 100 nm thick films of poly(p-phenylene vinylene).[21]

Working principle 
Schematic of a bilayer OLED: 1. Cathode (−), 2. Emissive Layer, 3. Emission of radiation, 4. Conductive Layer, 5. Anode (+)A typical OLED is composed of a layer of organic materials situated between two electrodes, the anode and cathode, all deposited on a substrate. The organic molecules are electrically conductive as a result of delocalization of pi electrons caused by conjugation over all or part of the molecule. These materials have conductivity levels ranging from insulators to conductors, and therefore are considered organic semiconductors. The highest occupied and lowest unoccupied molecular orbitals (HOMO and LUMO) of organic semiconductors are analogous to the valence and conduction bands of inorganic semiconductors.

Originally, the most basic polymer OLEDs consisted of a single organic layer. One example was the first light-emitting device synthesised by J. H. Burroughes et al., which involved a single layer of poly(p-phenylene vinylene). However multilayer OLEDs can be fabricated with two or more layers in order to improve device efficiency. As well as conductive properties, different materials may be chosen to aid charge injection at electrodes by providing a more gradual electronic profile,[22] or block a charge from reaching the opposite electrode and being wasted.[23] Many modern OLEDs incorporate a simple bilayer structure, consisting of a conductive layer and an emissive layer. More recent developments in OLED architecture improves quantum efficiency (up to 19%) by using a graded heterojunction.[24] In the graded heterojunction architecture, the composition of hole and electron-transport materials varies continuously within the emissive layer with a dopant emitter. The graded heterojunction architecture combines the benefits of both conventional architectures by improving charge injection while simultaneously balancing charge transport within the emissive region.[25]

During operation, a voltage is applied across the OLED such that the anode is positive with respect to the cathode. Anodes are picked based upon the quality of their optical transparency, electrical conductivity, and chemical stability.[26] A current of electrons flows through the device from cathode to anode, as electrons are injected into the LUMO of the organic layer at the cathode and withdrawn from the HOMO at the anode. This latter process may also be described as the injection of electron holes into the HOMO. Electrostatic forces bring the electrons and the holes towards each other and they recombine forming an exciton, a bound state of the electron and hole. This happens closer to the emissive layer, because in organic semiconductors holes are generally more mobile than electrons. The decay of this excited state results in a relaxation of the energy levels of the electron, accompanied by emission of radiation whose frequency is in the visible region. The frequency of this radiation depends on the band gap of the material, in this case the difference in energy between the HOMO and LUMO.

As electrons and holes are fermions with half integer spin, an exciton may either be in a singlet state or a triplet state depending on how the spins of the electron and hole have been combined. Statistically three triplet excitons will be formed for each singlet exciton. Decay from triplet states (phosphorescence) is spin forbidden, increasing the timescale of the transition and limiting the internal efficiency of fluorescent devices. Phosphorescent organic light-emitting diodes make use of spin–orbit interactions to facilitate intersystem crossing between singlet and triplet states, thus obtaining emission from both singlet and triplet states and improving the internal efficiency.

Indium tin oxide (ITO) is commonly used as the anode material. It is transparent to visible light and has a high work function which promotes injection of holes into the HOMO level of the organic layer. A typical conductive layer may consist of PEDOT:PSS[27] as the HOMO level of this material generally lies between the workfunction of ITO and the HOMO of other commonly used polymers, reducing the energy barriers for hole injection. Metals such as barium and calcium are often used for the cathode as they have low work functions which promote injection of electrons into the LUMO of the organic layer.[28] Such metals are reactive, so they require a capping layer of aluminium to avoid degradation.

Experimental research has proven that the properties of the anode, specifically the anode/hole transport layer (HTL) interface topography plays a major role in the efficiency, performance, and lifetime of organic light emitting diodes. Imperfections in the surface of the anode decrease anode-organic film interface adhesion, increase electrical resistance, and allow for more frequent formation of non-emissive dark spots in the OLED material adversely affecting lifetime. Mechanisms to decrease anode roughness for ITO/glass substrates include the use of thin films and self-assembled monolayers. Also, alternative substrates and anode materials are being considered to increase OLED performance and lifetime. Possible examples include single crystal sapphire substrates treated with gold (Au) film anodes yielding lower work functions, operating voltages, electrical resistance values, and increasing lifetime of OLEDs.[29]

Single carrier devices are typically used to study the kinetics and charge transport mechanisms of an organic material and can be useful when trying to study energy transfer processes. As current through the device is composed of only one type of charge carrier, either electrons or holes, recombination does not occur and no light is emitted. For example, electron only devices can be obtained by replacing ITO with a lower work function metal which increases the energy barrier of hole injection. Similarly, hole only devices can be made by using a cathode made solely of aluminium, resulting in an energy barrier too large for efficient electron injection.[30][31][32]

Material technologies Small molecules 
Alq3,[20] commonly used in small molecule OLEDsEfficient OLEDs using small molecules were first developed by Dr. Ching W. Tang et al.[20] at Eastman Kodak. The term OLED traditionally refers specifically to this type of device, though the term SM-OLED is also in use.

Molecules commonly used in OLEDs include organometallic chelates (for example Alq3, used in the organic light-emitting device reported by Tang et al.), fluorescent and phosphorescent dyes and conjugated dendrimers. A number of materials are used for their charge transport properties, for example triphenylamine and derivatives are commonly used as materials for hole transport layers.[33] Fluorescent dyes can be chosen to obtain light emission at different wavelengths, and compounds such as perylene, rubrene and quinacridone derivatives are often used.[34] Alq3 has been used as a green emitter, electron transport material and as a host for yellow and red emitting dyes.

The production of small molecule devices and displays usually involves thermal evaporation in a vacuum. This makes the production process more expensive and of limited use for large-area devices than other processing techniques. However, contrary to polymer-based devices, the vacuum deposition process enables the formation of well controlled, homogeneous films, and the construction of very complex multi-layer structures. This high flexibility in layer design, enabling distinct charge transport and charge blocking layers to be formed, is the main reason for the high efficiencies of the small molecule OLEDs.

Coherent emission from a laser dye-doped tandem SM-OLED device, excited in the pulsed regime, has been demonstrated.[35] The emission is nearly diffraction limited with a spectral width similar to that of broadband dye lasers.[36]

Researchers report luminescence from a single polymer molecule, representing the smallest possible organic light-emitting diode (OLED) device.[37] Scientists will be able to optimize substances to produce more powerful light emissions. Finally, this work is a first step towards making molecule-sized components that combine electronic and optical properties. Similar components could form the basis of a molecular computer.[38]

Polymer light-emitting diodes 
poly(p-phenylene vinylene), used in the first PLED[21]Polymer light-emitting diodes (PLED), also light-emitting polymers (LEP), involve an electroluminescent conductive polymer that emits light when connected to an external voltage. They are used as a thin film for full-spectrum colour displays. Polymer OLEDs are quite efficient and require a relatively small amount of power for the amount of light produced.

Vacuum deposition is not a suitable method for forming thin films of polymers. However, polymers can be processed in solution, and spin coating is a common method of depositing thin polymer films. This method is more suited to forming large-area films than thermal evaporation. No vacuum is required, and the emissive materials can also be applied on the substrate by a technique derived from commercial inkjet printing.[39][40] However, as the application of subsequent layers tends to dissolve those already present, formation of multilayer structures is difficult with these methods. The metal cathode may still need to be deposited by thermal evaporation in vacuum. An alternative method to vacuum deposition is to deposit a Langmuir-Blodgett film.

Typical polymers used in PLED displays include derivatives of poly(p-phenylene vinylene) and polyfluorene. Substitution of side chains onto the polymer backbone may determine the colour of emitted light[41] or the stability and solubility of the polymer for performance and ease of processing.[42]

While unsubstituted poly(p-phenylene vinylene) (PPV) is typically insoluble, a number of PPVs and related poly(naphthalene vinylene)s (PNVs) that are soluble in organic solvents or water have been prepared via ring opening metathesis polymerization.[43][44][45]

Phosphorescent materials 
Ir(mppy)3, a phosphorescent dopant which emits green light.[46]Main article: Phosphorescent organic light-emitting diode
Phosphorescent organic light emitting diodes use the principle of electrophosphorescence to convert electrical energy in an OLED into light in a highly efficient manner,[47][48] with the internal quantum efficiencies of such devices approaching 100%.[49]

Typically, a polymer such as poly(n-vinylcarbazole) is used as a host material to which an organometallic complex is added as a dopant. Iridium complexes[48] such as Ir(mppy)3[46] are currently the focus of research, although complexes based on other heavy metals such as platinum[47] have also been used.

The heavy metal atom at the centre of these complexes exhibits strong spin-orbit coupling, facilitating intersystem crossing between singlet and triplet states. By using these phosphorescent materials, both singlet and triplet excitons will be able to decay radiatively, hence improving the internal quantum efficiency of the device compared to a standard PLED where only the singlet states will contribute to emission of light.

Applications of OLEDs in solid state lighting require the achievement of high brightness with good CIE coordinates (for white emission). The use of macromolecular species like polyhedral oligomeric silsesquioxanes (POSS) in conjunction with the use of phosphorescent species such as Ir for printed OLEDs have exhibited brightnesses as high as 10,000 cd/m2.[50]

Device architectures Structure Bottom or top emission
Bottom or top distinction refers not to orientation of the OLED display, but to the direction that emitted light exits the device. OLED devices are classified as bottom emission devices if light emitted passes through the transparent or semi-transparent bottom electrode and substrate on which the panel was manufactured. Top emission devices are classified based on whether or not the light emitted from the OLED device exits through the lid that is added following fabrication of the device. Top-emitting OLEDs are better suited for active-matrix applications as they can be more easily integrated with a non-transparent transistor backplane. The TFT array attached to the bottom substrate on which AMOLEDs are manufactured are typically non-transparent, resulting in considerable blockage of transmitted light if the device followed a bottom emitting scheme.[51]
Transparent OLEDs
Transparent OLEDs use transparent or semi-transparent contacts on both sides of the device to create displays that can be made to be both top and bottom emitting (transparent). TOLEDs can greatly improve contrast, making it much easier to view displays in bright sunlight.[52] This technology can be used in Head-up displays, smart windows or augmented reality applications.
Graded Heterojunction
Graded heterojunction OLEDs gradually decrease the ratio of electron holes to electron transporting chemicals.[24] This results in almost double the quantum efficiency of existing OLEDs.
Stacked OLEDs
Stacked OLEDs use a pixel architecture that stacks the red, green, and blue subpixels on top of one another instead of next to one another, leading to substantial increase in gamut and color depth,[citation needed] and greatly reducing pixel gap. Currently, other display technologies have the RGB (and RGBW) pixels mapped next to each other decreasing potential resolution.
Inverted OLED
In contrast to a conventional OLED, in which the anode is placed on the substrate, an Inverted OLED uses a bottom cathode that can be connected to the drain end of an n-channel TFT especially for the low cost amorphous silicon TFT backplane useful in the manufacturing of AMOLED displays.[53]
Patterning technologies Patternable organic light-emitting devices use a light or heat activated electroactive layer. A latent material (PEDOT-TMA) is included in this layer that, upon activation, becomes highly efficient as a hole injection layer. Using this process, light-emitting devices with arbitrary patterns can be prepared.[54]

Colour patterning can be accomplished by means of laser, such as radiation-induced sublimation transfer (RIST).[55]

Organic vapour jet printing (OVJP) uses an inert carrier gas, such as argon or nitrogen, to transport evaporated organic molecules (as in organic vapour phase deposition). The gas is expelled through a micrometre-sized nozzle or nozzle array close to the substrate as it is being translated. This allows printing arbitrary multilayer patterns without the use of solvents.

Conventional OLED displays are formed by vapor thermal evaporation (VTE) and are patterned by shadow-mask. A mechanical mask has openings allowing the vapor to pass only on the desired location.

Like ink jet material depositioning, inkjet etching (IJE) deposits precise amounts of solvent onto a substrate designed to selectively dissolve the substrate material and induce a structure or pattern. Inkjet etching of polymer layers in OLED’s can be used to increase the overall out-coupling efficiency. In OLEDs, light produced from the emissive layers of the OLED is partially transmitted out of the device and partially trapped inside the device by total internal reflection (TIR). This trapped light is wave-guided along the interior of the device until it reaches an edge where it is dissipated by either absorption and/or emission. Inkjet etching can be used to selectively alter the polymeric layers of OLED structures to decrease overall TIR and increase out-coupling efficiency of the OLED. Compared to a non-etched polymer layer, the structured polymer layer in the OLED structure from the IJE process helps to decrease the TIR of the OLED device. IJE solvents are commonly organic instead of water based due to their non-acidic nature and ability to effectively dissolve materials at temperatures under the boiling point of water.[56]

Backplane technologies For a high resolution display like a TV, a TFT backplane is necessary to drive the pixels correctly. Currently, low temperature polycrystalline silicon (LTPS) - thin-film transistor (TFT) is used for commercial AMOLED displays. LTPS-TFT has variation of the performance in a display, so various compensation circuits have been reported.[57] Due to the size limitation of the excimer laser used for LTPS, the AMOLED size was limited. To cope with the hurdle related to the panel size, amorphous-silicon/microcrystalline-silicon backplanes have been reported with large display prototype demonstrations.[58]

Fabrication Transfer-printing is an emerging technology with the capability to assemble large numbers of parallel OLED and AMOLED devices under efficient conditions. Transfer-printing takes advantage of standard metal deposition, photolithography, and etching to create alignment marks on device substrates, commonly glass. Thin polymer adhesive layers are applied to enhance resistance to particles and surface defects. Microscale ICs are transfer-printed onto the adhesive surface and then baked to fully cure adhesive layers. An additional photosensitive polymer layer is then applied to the substrate to account for the topography caused by the printed ICs, reintroducing a flat surface. Photolithography and etching are performed to remove some polymer layers to uncover conductive pads on the ICs. Following this step, the anode layer is applied to the device backplane to form bottom electrode. OLED layers are then applied to the anode layer using conventional vapor deposition processes, and covered with a conductive metal electrode layer. Transfer-printing is currently capable of printing onto target substrates up to 500mm X 400mm. Expansion on this size limit is needed in order for transfer-printing to become a common process for the fabrication of large OLED/AMOLED displays.[59]

Advantages Further information: Comparison of CRT, LCD, Plasma, and OLED
 
Demonstration of a 4.1" prototype flexible display from SonyThe different manufacturing process of OLEDs lends itself to several advantages over flat panel displays made with LCD technology.

Lower cost in the future
OLEDs can be printed onto any suitable substrate by an inkjet printer or even by screen printing,[60] theoretically making them cheaper to produce than LCD or plasma displays. However, fabrication of the OLED substrate is more costly than that of a TFT LCD, until mass production methods lower cost through scalability. Roll-to-roll vapour-deposition methods for organic devices do allow mass production of thousands of devices per minute for minimal cost, although this technique also induces problems in that devices with multiple layers can be challenging to make because of registration, lining up the different printed layers to the required degree of accuracy.
Lightweight and flexible plastic substrates
OLED displays can be fabricated on flexible plastic substrates leading to the possible fabrication of flexible organic light-emitting diodes for other new applications, such as roll-up displays embedded in fabrics or clothing. As the substrate used can be flexible such as polyethylene terephthalate (PET),[61] the displays may be produced inexpensively.
Wider viewing angles and improved brightness
OLEDs can enable a greater artificial contrast ratio (both dynamic range and static, measured in purely dark conditions) and a wider viewing angle compared to LCDs because OLED pixels emit light directly. OLED pixel colors appear correct and unshifted, even as the viewing angle approaches 90° from normal.
Better power efficiency and thickness
LCDs filter the light emitted from a backlight, allowing a small fraction of light through. So, they cannot show true black. However, an inactive OLED element does not produce light or consume power, thus allowing true blacks.[62] Dismissing the backlight also makes OLEDs lighter because some substrates are not needed. This allows electronics potentially to be manufactured more cheaply, but, first, a larger production scale is needed, because OLEDs still somewhat are niche products.[63] When looking at top-emitting OLEDs, thickness also plays a role when talking about index match layers (IMLs). Emission intensity is enhanced when the IML thickness is 1.3–2.5 nm. The refractive value and the matching of the optical IMLs property, including the device structure parameters, also enhance the emission intensity at these thicknesses.[64]
Response time
OLEDs also can have a faster response time than standard LCD screens. Whereas LCD displays are capable of between 1 and 16 ms response time offering a refresh rate of 60 to 480 Hz, an OLED theoretically can have a response time less than 0.01 ms, enabling a refresh rate up to 100,000 Hz .[citation needed]. OLEDs also can be run as a flicker display, similar to a CRT, in order to eliminate the sample-and-hold effect that creates motion blur on OLEDs.[65]
Disadvantages  This article's Criticism or Controversy section may compromise the article's neutral point of view of the subject. Please integrate the section's contents into the article as a whole, or rewrite the material. (November 2011)

 
LEP (Light Emitting Polymer) display showing partial failure
An old OLED display showing wearCurrent costs
OLED manufacture currently requires process steps that make it extremely expensive. Specifically, it requires the use of low-temperature polysilicon backplanes; LTPS backplanes, in turn, require laser annealing from an amorphous silicon start. This part of the manufacturing process for AMOLEDs starts with similar process costs to a standard LCD, and then adds a further process, lengthening the entire manufacturing step. Currently, large-area glass substrates are out of scale for AMOLED devices.[citation needed]
Lifespan
The biggest technical problem for OLEDs was the limited lifetime of the organic materials. One 2008 technical report on an OLED TV panel found that "After 1,000 hours the blue luminance degraded by 12%, the red by 7% and the green by 8%."[66] In particular, blue OLEDs historically have had a lifetime of around 14,000 hours to half original brightness (five years at 8 hours a day) when used for flat-panel displays. This is lower than the typical lifetime of LCD, LED or PDP technology. Each currently is rated for about 25,000–40,000 hours to half brightness, depending on manufacturer and model.[67][68] Degradation occurs because of the accumulation of nonradiative recombination centers and luminescence quenchers in the emissive zone. It is said that the chemical breakdown in the semiconductors occurs in four steps: 1) recombination of charge carriers through the absorption of UV light, 2) hemolytic dissociation, 3)subsequent radical addition reactions that form π radicals, and 4) disproportionation between two radicals resulting in hydrogen-atom transfer reactions.[69] However, some manufacturers' displays aim to increase the lifespan of OLED displays, pushing their expected life past that of LCD displays by improving light outcoupling, thus achieving the same brightness at a lower drive current.[70][71] In 2007, experimental OLEDs were created which can sustain 400 cd/m2 of luminance for over 198,000 hours for green OLEDs and 62,000 hours for blue OLEDs.[72]
Color balance issues
Additionally, as the OLED material used to produce blue light degrades significantly more rapidly than the materials that produce other colors, blue light output will decrease relative to the other colors of light. This variation in the differential color output will change the color balance of the display and is much more noticeable than a decrease in overall luminance.[73] This can be avoided partially by adjusting color balance, but this may require advanced control circuits and interaction with the user, which is unacceptable for some users. More commonly, though, manufacturers optimize the size of the R, G and B subpixels to reduce the current density through the subpixel in order to equalize lifetime at full luminance. For example, a blue subpixel may be 100% larger than the green subpixel. The red subpixel may be 10% smaller than the green.
Efficiency of blue OLEDs
Improvements to the efficiency and lifetime of blue OLEDs is vital to the success of OLEDs as replacements for LCD technology. Considerable research has been invested in developing blue OLEDs with high external quantum efficiency as well as a deeper blue color.[74][75] External quantum efficiency values of 20% and 19% have been reported for red (625 nm) and green (530 nm) diodes, respectively.[76][77] However, blue diodes (430 nm) have only been able to achieve maximum external quantum efficiencies in the range of 4% to 6%.[78]
Water damage
Water can damage the organic materials of the displays. Therefore, improved sealing processes are important for practical manufacturing. Water damage especially may limit the longevity of more flexible displays.[79]
Outdoor performance
 This section does not cite any references or sources. Please help improve this section by adding citations to reliable sources. Unsourced material may be challenged and removed. (November 2013)
As an emissive display technology, OLEDs rely completely upon converting electricity to light, unlike most LCDs which are to some extent reflective. e-paper leads the way in efficiency with ~ 33% ambient light reflectivity, enabling the display to be used without any internal light source. The metallic cathode in an OLED acts as a mirror, with reflectance approaching 80%, leading to poor readability in bright ambient light such as outdoors. However, with the proper application of a circular polarizer and antireflective coatings, the diffuse reflectance can be reduced to less than 0.1%. With 10,000 fc incident illumination (typical test condition for simulating outdoor illumination), that yields an approximate photopic contrast of 5:1.
Power consumption
While an OLED will consume around 40% of the power of an LCD displaying an image that is primarily black, for the majority of images it will consume 60–80% of the power of an LCD. However, an OLED can use more than three times as much power to display an image with a white background, such as a document or web site.[80] This can lead to reduced battery life in mobile devices, when white backgrounds are used.
Manufacturers and commercial uses  This section is outdated. Please update this article to reflect recent events or newly available information. (October 2013)

 
Magnified image of the AMOLED screen on the Google Nexus One smartphone using the RGBG system of the PenTile Matrix Family.
A 3.8 cm (1.5 in) OLED display from a Creative ZEN V media playerOLED technology is used in commercial applications such as displays for mobile phones and portable digital media players, car radios and digital cameras among others. Such portable applications favor the high light output of OLEDs for readability in sunlight and their low power drain. Portable displays are also used intermittently, so the lower lifespan of organic displays is less of an issue. Prototypes have been made of flexible and rollable displays which use OLEDs' unique characteristics. Applications in flexible signs and lighting are also being developed.[81] Philips Lighting have made OLED lighting samples under the brand name "Lumiblade" available online [82] and Novaled AG based in Dresden, Germany, introduced a line of OLED desk lamps called "Victory" in September, 2011.[83]

OLEDs have been used in most Motorola and Samsung color cell phones, as well as some HTC, LG and Sony Ericsson models.[84] Nokia has also introduced some OLED products including the N85 and the N86 8MP, both of which feature an AMOLED display. OLED technology can also be found in digital media players such as the Creative ZEN V, the iriver clix, the Zune HD and the Sony Walkman X Series.

The Google and HTC Nexus One smartphone includes an AMOLED screen, as does HTC's own Desire and Legend phones. However due to supply shortages of the Samsung-produced displays, certain HTC models will use Sony's SLCD displays in the future,[85] while the Google and Samsung Nexus S smartphone will use "Super Clear LCD" instead in some countries.[86]

OLED displays were used in watches made by Fossil (JR-9465) and Diesel (DZ-7086).

Other manufacturers of OLED panels include Anwell Technologies Limited (Hong Kong),[87] AU Optronics (Taiwan),[88] Chimei Innolux Corporation (Taiwan),[89] LG (Korea),[90] and others.[91]

In 2009, Shearwater Research introduced the Predator as the first color OLED diving computer available with a user replaceable battery.[92][93]

DuPont stated in a press release in May 2010 that they can produce a 50-inch OLED TV in two minutes with a new printing technology. If this can be scaled up in terms of manufacturing, then the total cost of OLED TVs would be greatly reduced. DuPont also states that OLED TVs made with this less expensive technology can last up to 15 years if left on for a normal eight hour day.[94][95]

The use of OLEDs may be subject to patents held by Eastman Kodak, DuPont, General Electric, Royal Philips Electronics, numerous universities and others.[96] There are by now thousands of patents associated with OLEDs, both from larger corporations and smaller technology companies.

RIM, the maker of BlackBerry smartphones, have unofficially announced that their upcoming BlackBerry 10 devices will use OLED displays. This marks the upcoming BB10 smartphones as some of the first to use OLED displays.

Foldable OLED smartphones could be as much as a decade away because of the cost of producing them. There is a relatively high failure rate when producing these screens. As little as a speck of dust can ruin a screen during production. Creating a battery that can be folded is another hurdle.[97]

Fashion Textiles incorporating OLEDs are an innovation in the fashion world and pose for a way to integrate lighting to bring inert objects to a whole new level of fashion. The hope is to combine the comfort and low cost properties of textile with the OLEDs properties of illumination and low energy consumption. Although this scenario of illuminated clothing is highly plausible, challenges are still a road block. Some issues include: the lifetime of the OLED, rigidness of flexible foil substrates, and the lack of research in making more fabric like photonic textiles.[98]

Samsung applications By 2004 Samsung, South Korea's largest conglomerate, was the world's largest OLED manufacturer, producing 40% of the OLED displays made in the world,[99] and as of 2010 has a 98% share of the global AMOLED market.[100] The company is leading the world of OLED industry, generating $100.2 million out of the total $475 million revenues in the global OLED market in 2006.[101] As of 2006, it held more than 600 American patents and more than 2800 international patents, making it the largest owner of AMOLED technology patents.[101]

Samsung SDI announced in 2005 the world's largest OLED TV at the time, at 21 inches (53 cm).[102] This OLED featured the highest resolution at the time, of 6.22 million pixels. In addition, the company adopted active matrix based technology for its low power consumption and high-resolution qualities. This was exceeded in January 2008, when Samsung showcased the world's largest and thinnest OLED TV at the time, at 31 inches (78 cm) and 4.3 mm.[103]

In May 2008, Samsung unveiled an ultra-thin 12.1 inch (30 cm) laptop OLED display concept, with a 1,280×768 resolution with infinite contrast ratio.[104] According to Woo Jong Lee, Vice President of the Mobile Display Marketing Team at Samsung SDI, the company expected OLED displays to be used in notebook PCs as soon as 2010.[105]

In October 2008, Samsung showcased the world's thinnest OLED display, also the first to be "flappable" and bendable.[106] It measures just 0.05 mm (thinner than paper), yet a Samsung staff member said that it is "technically possible to make the panel thinner".[106] To achieve this thickness, Samsung etched an OLED panel that uses a normal glass substrate. The drive circuit was formed by low-temperature polysilicon TFTs. Also, low-molecular organic EL materials were employed. The pixel count of the display is 480 × 272. The contrast ratio is 100,000:1, and the luminance is 200 cd/m2. The colour reproduction range is 100% of the NTSC standard.

In the same month, Samsung unveiled what was then the world's largest OLED Television at 40-inch with a Full HD resolution of 1920 × 1080 pixels.[107] In the FPD International, Samsung stated that its 40-inch OLED Panel is the largest size currently possible. The panel has a contrast ratio of 1,000,000:1, a colour gamut of 107% NTSC, and a luminance of 200 cd/m2 (peak luminance of 600 cd/m2).

At the Consumer Electronics Show (CES) in January 2010, Samsung demonstrated a laptop computer with a large, transparent OLED display featuring up to 40% transparency[108] and an animated OLED display in a photo ID card.[109]

Samsung's latest AMOLED smartphones use their Super AMOLED trademark, with the Samsung Wave S8500 and Samsung i9000 Galaxy S being launched in June 2010. In January 2011 Samsung announced their Super AMOLED Plus displays, which offer several advances over the older Super AMOLED displays: real stripe matrix (50% more sub pixels), thinner form factor, brighter image and an 18% reduction in energy consumption.[110]

At CES 2012, Samsung introduced the first 55" TV screen that uses Super OLED technology.[111]

On January 8, 2013, at CES Samsung unveiled a unique curved 4K Ultra S9 OLED television, which they state provides an "IMAX-like experience" for viewers.[112]

On August 13, 2013, Samsung announced availability of a 55-inch curved OLED TV (model KN55S9C) in the US at a price point of $8999.99.[113]

On September 6, 2013, Samsung launched its 55-inch curved OLED TV (model KE55S9C) in the United Kingdom with John Lewis.[114]

Samsung introduced the Galaxy Round smartphone in the Korean market in October 2013. The device features a 1080p screen, measuring 5.7 inches (14 cm), that curves on the vertical axis in a rounded case. The corporation has promoted the following advantages: A new feature called "Round Interaction" that allows users to look at information by tilting the handset on a flat surface with the screen off, and the feel of one continuous transition when the user switches between home screens.[115]

Sony applications 
Sony XEL-1, the world's first OLED TV.[116] (front)The Sony CLIÉ PEG-VZ90 was released in 2004, being the first PDA to feature an OLED screen.[117] Other Sony products to feature OLED screens include the MZ-RH1 portable minidisc recorder, released in 2006[118] and the Walkman X Series.[119]

At the 2007 Las Vegas Consumer Electronics Show (CES), Sony showcased 11-inch (28 cm, resolution 960×540) and 27-inch (68.5 cm), full HD resolution at 1920 × 1080 OLED TV models.[120] Both claimed 1,000,000:1 contrast ratios and total thicknesses (including bezels) of 5 mm. In April 2007, Sony announced it would manufacture 1000 11-inch (28 cm) OLED TVs per month for market testing purposes.[121] On October 1, 2007, Sony announced that the 11-inch (28 cm) model, now called the XEL-1, would be released commercially;[116] the XEL-1 was first released in Japan in December 2007.[122]

In May 2007, Sony publicly unveiled a video of a 2.5-inch flexible OLED screen which is only 0.3 millimeters thick.[123] At the Display 2008 exhibition, Sony demonstrated a 0.2 mm thick 3.5 inch (9 cm) display with a resolution of 320×200 pixels and a 0.3 mm thick 11 inch (28 cm) display with 960×540 pixels resolution, one-tenth the thickness of the XEL-1.[124][125]

In July 2008, a Japanese government body said it would fund a joint project of leading firms, which is to develop a key technology to produce large, energy-saving organic displays. The project involves one laboratory and 10 companies including Sony Corp. NEDO said the project was aimed at developing a core technology to mass-produce 40 inch or larger OLED displays in the late 2010s.[126]

In October 2008, Sony published results of research it carried out with the Max Planck Institute over the possibility of mass-market bending displays, which could replace rigid LCDs and plasma screens. Eventually, bendable, see-through displays could be stacked to produce 3D images with much greater contrast ratios and viewing angles than existing products.[127]

Sony exhibited a 24.5" (62 cm) prototype OLED 3D television during the Consumer Electronics Show in January 2010.[128]

In January 2011, Sony announced the PlayStation Vita handheld game console (the successor to the PSP) will feature a 5-inch OLED screen.[129]

On February 17, 2011, Sony announced its 25" (63.5 cm) OLED Professional Reference Monitor aimed at the Cinema and high end Drama Post Production market.[130]

On June 25, 2012, Sony and Panasonic announced a joint venture for creating low cost mass production OLED televisions by 2013.[131]

LG applications As of 2010, LG Electronics produced one model of OLED television, the 15 inch 15EL9500[132] and had announced a 31" (78 cm) OLED 3D television for March 2011.[133] On December 26, 2011, LG officially announced the "world's largest 55" OLED panel" and featured it at CES 2012.[134] In late 2012, LG announces the launch of the 55EM9600 OLED television in Australia.[135]

Mitsubishi applications Lumiotec is the first company in the world developing and selling, since January 2011, mass-produced OLED lighting panels with such brightness and long lifetime. Lumiotec is a joint venture of Mitsubishi Heavy Industries, ROHM, Toppan Printing, and Mitsui & Co. On June 1, 2011, Mitsubishi installed a 6-meter OLED 'sphere' in Tokyo's Science Museum. [136]

Recom Group/video name tag applications On January 6, 2011, Los Angeles based technology company Recom Group introduced the first small screen consumer application of the OLED at the Consumer Electronics Show in Las Vegas. This was a 2.8" (7 cm) OLED display being used as a wearable video name tag.[137] At the Consumer Electronics Show in 2012, Recom Group introduced the world's first video mic flag incorporating three 2.8" (7 cm) OLED displays on a standard broadcasters mic flag. The video mic flag allowed video content and advertising to be shown on a broadcasters standard mic flag.[138]